SuperSpec

SuperSpec

Tuesday 27 December 2016

Xmas Present

Just done a test run of my Xmas present:


It isn't just a hat though, I have plenty of those, this one is special in that it has Bluetooth headphones built in     Test run a huge success, very comfy and warm (although not heavy so I can probably continue to use it in Summer),  headphones had plenty of volume, even though the exhaust is now REALLY blowing and I listened to a whole episode of R4 Friday Night Comedy, on my round trip.
 
The only slight drawback is that if the mask covers my nose then my glasses immediately steam up.   So I have to pull it down slightly to expose my nose  (Most of us drive with glasses on since one chap had hid windscreen shatter, and it is safety glass rather than laminated so he was showered with glass).  But nose didn't get cold
 
Very successful

Monday 19 December 2016

Fitted Cargo Net

It's a bit cold to tinker at the moment, but just had a successful 15 mins with her.  I have had 2 'niggling' problems that I have been living with for some time:

1.  The carpet in the passenger footwell has to be loose so you can access the bolts holding the exhaust heat shield.   It is held in by velcro, but occasionally the wind coming into the side of the footwell gets behind the carpet and dislodges it.

2.  Now that plastic bags have been declared 'persona non grata' I've got in the habit of carrying one of the reusable shopping bags  (known as 'envirosacs' apparently)  around in the car, for ad-hoc visits to supermarkets.   The glove box has got a bit full so I normally just chuck it in the passenger footwell, but three times recently it has actually been 'sucked' out of the footwell and flew out of the car  (the aerodynamics of these cars is totally off-the-plot).    Cue a U-turn (once in total darkness) and a drive back to try and find it.

So I realised I could cure both problems by fitting one of these mini cargo nets to the side of the car.    Here is the result:



And with the envirosac in:   (And actually room for more, hat, gloves...)
 

Job done.  The carpet will never come loose and the bag will never get sucked out.

Tuesday 13 December 2016

Brake lights

Been a bit quiet recently but took her out 3 times last week.   Nice run down to see latest grand daughter on Sunday.    The engine loves this cool damp air, she ran like a sewing machine and once again I found I was having to force myself to slow down.   I really don't know why people SORN the cars over the winter, it is lovely.   Temperature stabilised at 86C, which I am quite happy with.  It could run hotter but anything above 80C is enough to boil off contaminates in the oil.

But on the way back, as it was getting dark, I noticed the brake lights weren't working again.  The warning glow behind the dash next to my right knee once again proved it's worth, as I would never have known otherwise.

This normally means the adjustment has vibrated out, but this time that didn't seem to be the problem.   Taking the switch out it all worked fine, but once I mounted it back it stopped working.   Wiggling the wires made it flicker so I put new spades on both wires.   Didn't help.   Eventually I figured out the contacts inside the switch had become intermittent.  You may recall the original switch had corroded and I had replaced it with one of a Mini that I got for 99p.   I guess 3 years is not bad for 99p.

So this time I decided to splash out and get one from a Land Rover Defender on the basis that might be heavier duty.  Cost the grand sum of £3.25

LAND ROVER BRAKE LIGHT SWITCH, LAND ROVER, DISCOVERY, ETC, MINI
Fitted it and everything was fine.   The only problem was getting the adjustment right.   Up to now I have adjusted the whole mounting unit, but as this has to be mounted using self-tappers (If nuts/bolt used then it needs a second person to access the underside of the pedal box) these are not designed to be repeatedly taken in and out so have now worn.   So had to come up with an alternative solution.   Have always been happier working with wood than metal (Remember the wooden clutch cable adjuster with is working perfectly), probably because I did woodwork at school rather than metalwork.  
So I decided to use a wooden wedge, initially cutting it roughly to size and then using a Surform plane to gradually reduce the length until the switch was in exactly the right position.
 

Success, very solid fit and lights come on perfectly when pedal depressed.